Note: GTW = 4-wire, GTWO = 2-wire
Common GTW(O) Parts:
Board bracket stands (grey guides)
XG3A cable [CAN CPU] (CPU to CPU) (LCECAN TO LCECAN CABLE (XG3) (HF) L=10M)
KM756706G10 (10M)
*G05 (5M)
*G01 (1M)
XG3A terminating resistor [120 ohm]
LCEGTW parts:
GTW board
XG1B 4-wire GTW cable (GTW to GTW)
KM801740G07 [7 meter]
KM713255G01 [8 meter]
KM801740G15 [15 meter]
KM801740G35 [35 meter]
XG1B terminating resistor
XM13 Cable (CPU to GTW) [700 mm]
LCEGTWO2 parts:
LCEGTWO2 board v3
XH12 to X3 & XS1 splitter cable (XH12 to GTWO)
XG1B 2-wire GTWO cable (GTWO to GTWO)
Optional LCEGTWO2 parts:
Power supply [110v to 24v step-down]
X2 cable [Power supply to GTWO]
To test up to 1100 pounds, request P/N KM50011956R02
To test up to 2200 pounds, request P/N KM50011954R02
To test up to 2860 pounds, request P/N KM50011955R02
To test up to 4400 pounds, request P/N KM50011958R02
To test up to 5730 pounds, request P/N KM50011957R02
1/4-20 x 1 Zinc Plated Self Clinching Stud
1/4-20 18-8 Stainless Steel Wing Nut
Fastenal Part No. (SKU)
25 pack: 1170910
Individual: 70910
GUIDE RAIL OIL COLLECTOR
XS2 Terminating Resistor
Adjusting interface list:
For programming COP MUL boards (assigning proper push button id's):
Laptop with licensed F2KConfig software
KM829082G02 MUL cable interface
Common boards:
Adon 3:
CCBN2 (Beam box, cartop box board):
CPU:
DCBG (PCB, MOTION CONTROL BOARD):
HAS:
GTW:
KNSMUL:
KRMRIF (remote monitoring):
Interface between the COP and the CCBN. This board functions as the telephone amongst other things.
Note: could not find on spares.
Proximity switch for NMX:
REC:
Star of Life (2 per elevator needed on almost every elevator, but none are ever sent):
Terminating resistors:
4-pin XG1 for GTW boards
2-pin XG3 for car grouping
MUL board alarm terminating jumper (J4)
Used when dual COP's are installed into a single cab. Not often required, but a nail in the coffin if one is ever needed.
Symptoms if one is bad: Pressing an alarm button will initiate an emergency call.
Could only find through parts.kone.com, not spares.
Security machine screws 10-24:
Stickers:
Less commonly used in our region:
Antec test tags
To test up to 1100 pounds, request P/N KM50011956R02
To test up to 2200 pounds, request P/N KM50011954R02
To test up to 2860 pounds, request P/N KM50011955R02
To test up to 4400 pounds, request P/N KM50011958R02
To test up to 5730 pounds, request P/N KM50011957R02
EAQ:
ETSL 3:
Fire status board:
Unfortunately fire status panels sometimes arrive without the boards.
120 ohm jumper needed with each board (required, but does not ship with) KM800385
For reference only in case one is ever needed: MURR 24V DC power supply KM280783
Firewire:
Gateway duplexing kit:
GTWO2:
For reference only in case one is ever needed: MURR 24V DC power supply KM280783
Ribbon cable | Kone connect:
Unsure on where to obtain.
VTC:
Not used often in our local. Likelihood of robbing Peter to pay Paul is low if one is needed.
Other common parts:
Unlocking devices:
Hand is determined by the strike when looking at the door from the inside of the elevator.
I.E. If the strike is on the right, it's right hand.
Left hand short arm (yellow bag)
Left hand long arm (yellow bag)
Right hand short arm (blue bag)
Right hand long arm (blue bag)
Machine screws for COP's:
#10-24 Button Head (low-profile) Socket Cap Screw, partially threaded (3/4" grip), 2" length, 18-8 stainless, 3 mm hex
Pickup roller assemblies (Interlock):
Hand is determined by the strike when looking at the door from the inside of the elevator.
I.E. If the strike is on the right, it's right hand.
Left hand interlock:
Right hand interlock:
-